Western Energy Sales
Manufacturer Representative
Common Valve Terms
Actuator: Device used to operate a valve using electric, pneumatic or hydraulic means. Often used for remote control
or sequencing of valve operations.

Alloy steel: A steel consisting primarily of iron with some percentage of one or more other elements such as
chromium, nickel, manganese, or vanadium deliberately added to enhance its properties.

Ambient temperature:
The prevailing temperature of the environment immediately surrounding an object.                         
generally considered to be -20° F to +100° F.

Austenitic stainless steel: The common stainless steel, where the primary micro structure is austenite and the
composition primarily iron but also includes both chromium and nickel. The steels are designated as 300 series such as
304, 316, CF8M, etc.

Bevel gear operator: Device facilitating operation of a gate or globe valve by means of a set of bevel gears having the
axis of the pinion gear at right angles to that of the larger ring gear. The reduction ratio of this gear set determines the
multiplication of torque achieved.

Back seat: A shoulder on the stem of a gate or globe valve which seals against a mating surface inside the bonnet to
prevent leakage of media through the bonnet stuffing box when the valve is fully opened.

Ball: The closure element of a ball valve.

Ball valve: A valve using a spherical closure element which is rotated through 90º to open and close the valve.

Body: The principle pressure containing part of a valve in which the closure element and seats are located.

Bolted bonnet: A bonnet which is connected to a valve body with bolts or studs and nuts.

Bolted construction: Describes a valve construction in which the pressure shell elements (such as body and closures of
a trunnion ball valve) are bolted together and so can be taken apart and repaired in the field.

Bonnet: The top part of a valve, attached to the body, which contains the packing gland, guides the stem, and adapts to
extensions or operators.

Bore (or port): The inside diameter of the smallest opening through a valve, e. g., inside diameter of a seat ring, diameter
of hole through ball in a ball valve.

Butt weld end (BW): The end connection of a valve suitably prepared for butt welding to a connecting pipe.

Carbon steel (CS): Iron containing carbon in the form of carbides, about 0.1 to 0.3 percent carbon with no other alloying
elements other than the sulfur, phosphorus, and other elements present in almost all steels.

Cast iron: The common term for cast gray iron or iron containing flake carbon in the range of _% to 2 _%. Cast iron is
brittle, exhibiting very little ductility before fracturing.

Casting: A product or the act of producing a product made by pouring molten metal into a mold and allowing it to solidify,
thus taking the shape of the mold.

Charpy impact test: A destructive mechanical test conducted on a precisely machined coupon of steel to be tested. The
coupon is clamped in a special machine and subjected to lateral hammer blow. The test provides a relative measure of the
toughness of the steel or its resistance to shock or impact loads and is usually required for material used in low
temperature applications.

Check valve: A one-directional valve which is opened by the fluid flow in one direction and closed automatically when the
flow stops or is reversed.

Clapper: The hinged closure element of a swing check valve.

Closure: The ends of a bolted construction ball valve, bolted to the body, which often retain the seat rings.

Closure element: The moving part of a valve, positioned in the flow stream, which controls the flow through the valve, e.
g., wedge, plug, clapper, ball.

Cv: Flow coefficient expressed as the number of gallons of water that would flow through an opening, such as a valve port,
in 1 minute under a differential pressure of 1 psi.

CWP: Cold working pressure - the maximum allowable pressure under non-shock conditions at ambient temperature ( -20°
F to +100° F).

Dezincification: A form of pitting corrosion which attacks certain zinc bearing copper-based alloys, often called "yellow
brasses", when in contact with sea water or fresh water that is high in oxygen and carbon dioxide. (ASTM B61 and B62 are
"red brasses" and not susceptible to dezincification.)

Double block and bleed: The capability of a valve under pressure to obtain a seal across both the upstream and
downstream seat rings and to have its body cavity bled down to atmospheric pressure.

Drain plug: A fitting at the bottom of a valve, the removal of which permits draining and flushing the body cavity.

Elastomer: A natural or synthetic elastic material, often used for o-ring seals. Typical materials are viton, buna-n, EPDM
(ethylene propylene dimonomer), etc.

End connection: The type of connection supplied on the ends of a valve which allows it to be connected to piping - may
be weld end, flanged end, threaded or socket weld.

Face-to-face: The overall dimension from the inlet face of a valve to the outlet face of a valve (one end to another)
allowing valves of the same size and pressure class to be mutually interchangeable, regardless of manufacturer.

Facing: The finish of the gasket contact surface of a flange.

Fitting: Any component, other than valves, used with pipe as part of the pressure system and normally referring to items
covered by a national standard.

Flat Face (FF): A flange surface in which the gasket sealing area is the entire surface from the ID to the outside edge.
Usually used for class 125 cast iron valves.

Fire safe: A valve design that is capable of passing a fire test with specified limits on leakage to the atmosphere and
downstream after being closed subsequent to fire exposure.

Floating ball: A ball valve design in which the ball is not rigidly held on its rotational axis and so is free to float between the
seat rings.

Float valve: A valve which automatically opens or closes as the level of a liquid changes. The valve is operated
mechanically by a float which rests on the top of the liquid.

Forging: A metalworking process that involves hammering or squeezing, with or without a die, at hot working temperatures
to form a specific shape.

Full bore (full port): Describes a valve in which the bore (port) is nominally equal to the bore of the connecting pipe.

Full penetration weld: Describes the type of weld wherein the weld metal extends through the complete thickness of the
parts being joined.

Gasket: A component whose purpose is to seal a joint between two larger components, softer than the surfaces of the joint
being sealed and usually squeezed by means of bolting to effect the seal.

Gate: The closure element of a gate valve (sometimes called wedge or disc).

Gate valve: A straight through pattern valve in which closure element is a wedge situated between two fixed seating
surfaces, with means to move it in or out of the flow stream in a direction perpendicular to the pipeline axis. Used as a block
valve, or on-off valve.

Gland or gland bushing: The part of the valve which retains or compresses the stem packing in a stuffing box.

Gland follower or gland flange: The component used to hold down or retain the gland in the stuffing box.

Globe valve: A valve whose closure element is a flat disc or conical plug sealing on a seat which is usually parallel to the
flow axis. Can be used for throttling services.

Graphite:
Flexible carbon material used to make gaskets and packing. The gaskets may be flat graphite sheet or have
metal inserts for added strength. The packing is a combination of lattice braided rings used as anti-extrusion or wiper rings
and die-formed rings which are compressed to effect the seal.

Grease fitting: A device which permits injection of grease into a bearing surface.

Hand wheel: A wheel-shaped valve operating device intended to be grasped with one or both hands which allows turning
the valve stem or operator shaft to which it is attached.

Hard facing: A surface preparation in which an alloy is deposited on a metal surface usually by weld overlay to increase
resistance to abrasion and or corrosion.

Heat analysis: A chemical analysis conducted by a foundry immediately prior to pouring which measures the exact
chemical composition of a particular batch of molten metal.

Heat treatment:
Describes any process or procedure by which the internal structure of steel is altered by heating to
produce desired physical and mechanical characteristics.

Hot tap: A connection made to a pipeline while the line is under pressure or in service. A special procedure is required to
make an opening in the pipe without leaking any of the line contents.

Hot tears: A defect occurring in castings caused where partially solidified or weak, newly solidified sections are subjected
to a pull resulting from the contraction of thinner parts that have solidified earlier. A hot tear is an intergranular failure.

Huey test: A corrosion resistance test for stainless steels, most useful for predicting resistance to intergranular corrosion.

Hydrostatic test: A pressure test in which a valve is tested with water to detect leaks - may be a shell test or a seat
closure test.

IBBM: Iron body, bronze mounted - common term for valves with cast iron body and bonnet and bronze trim (seating
surfaces, stem, bushings).

ID: The measurement of the inside diameter of a circular part.

ISRS: Inside screw, rising stem - common term for any valve design in which the stem threads are exposed to the fluid
below the packing and the stem rises up through the packing when the valve is opened.

Lever: A handle type operating device for quarter-turn valves.

Liquid penetrant inspection: A nondestructive method of detecting the presence of surface cracks and imperfections
through use of a special red dye. Abbreviated as LPI or PT.

Locking device: Any valve attachment whose purpose is to prevent the operation of the valve by unauthorized persons.

Magnetic particle inspection: A nondestructive method of detecting the presence of surface cracks and imperfections
through use of fine iron particles in an electrical field. Abbreviated as MPI or MT.

Material Test Reports (MTR's): Certificates provided by the steel manufacturer indicating the chemical analysis and
mechanical properties of a specific batch of steel traced by sequentially assigned heat numbers or codes.

Mold: A hollow cavity, frequently in packed sand, for giving a desired shape to a material in a molten or plastic shape.

NPS: Nominal pipe size - dimensionless number used to indicate sizes of pressure pipe and valves - used interchangeably
with valve size in inches.

NPT: National Pipe Taper - standard tapered thread for pressure pipe and components. Requirements defined in ASEM B1.
20.1.

NRS: Non-rising stem - A gate valve having its stem threaded into the gate. As the stem turns the gate moves but the stem
does not rise. Stem threads are exposed to the line fluid.

OD: The measurement of the outside diameter of a circular part.

O-ring: An elastomeric or synthetic seal ring of circular cross section.

OS&Y: Outside Screw & Yoke - A valve design in which the stem threads are above the packing gland or outside the valve
body and there is a yoke to support the top or outer end of the stem.

Packing: The deformable sealing material inserted into a valve stuffing box which when compressed by the gland provides
a tight seal about the stem.

Pattern:
A duplicate made of wood or metal of a part to be cast. Used to form the mold into which the molten metal is
poured.

Pinhole: Numerous small gas holes at the surface or just below the surface of castings, generally occurring in the thicker
parts of the casting as a reduction in the solubility of gases in the metal as the metal cools.

Pinion shaft:
The external input shaft of certain gear operators which drive the internal reduction gearing.

Plastics: A broad classification covering a variety of non-metallic, synthetic or organic materials capable of being molded
or formed into desired shapes. Typical materials include nylons and tetrafluoroethylenes such as Teflon.

PMI: Positive material identification - a method for cross checking the identity of a piece of material, often using a portable
spectrometer, usually with x-rays (TN 9266, nuclear analyzer) or a welding arc (Arc Met 900, optical spectrometer).

Pneumatic test
: A test in which a valve is tested with air - usually a seat closure test.

Porosity: A defect found in castings or welds consisting of gas bubbles or voids in the solidified metal.

Position indicator: Any external device which visually indicates the open and closed position of valve.

Pressure class: A pressure rating expressed as a dimensionless number. The class rating charts give actual pounds per
square inch maximum allowable pressure at a given temperature.

Pressure-Temperature Ratings: The maximum allowable working pressures at specified temperatures. For steel valves,
the ratings are defined by "classes" and found in ASME B16.34. For iron and bronze valves, the ratings are defined in the
applicable MSS specifications.

Product Analysis: The chemical analysis of a material done on a finished component to show compliance with the material
specifications. Usually has tolerances defined for each element to allow for differences in the completed product compared
to the molten metal.

PSI: Pounds per square inch - the force per unit area exerted against a resisting body.

Ra: Abbreviation for "arithmetic average roughness height" - the measure of the roughness of a surface expressed in
microinches. The higher the number, the rougher the surface. Used to designated the desired surface finish for end flange
raised faces.

Radiographic inspection: A nondestructive inspection method using x-rays to locate internal flaws in castings, fabricated
parts and welds. Abbreviated as RT.

Raised faced (RF): The raised area of a flange face which is the gasket sealing surface between mating flanges. Defined
in ASME B16.5. Class 150 and 300 valves have 0.06" RF and Classes 600 and up have a 0.25" RF.

Reduced port (RP): A valve port opening that is smaller than the line size or the valve end connection size.

Ring type joint (RTJ): A flange connection using a specially shaped soft metal ring as a gasket. Generally used on high
pressure valves. May be the body and bonnet connection and/or the end flange connection.

Resilient seat: A valve seat containing a soft seal such as an o-ring or plastic to assure tight shut-off.

Rim pull: The force required at the edge of the handwheel to generate the required torque at the center of the handwheel.

Rising stem (RS):  A valve stem with threads arranged so that as the stem turns, the threads engage a stationary
threaded area and lift the stem along with the closure element attached to it.

Schedule: A system for indicating the wall thickness of pipe. The higher the schedule number, the thicker the wall for a
certain pipe size.

Seal weld: A weld that does not contribute anything to the mechanical integrity of an assembly, but is made purely to seal
or prevent leakage from, for instance, a threaded joint.

Seat: The part of a valve against which the closure element effects shut-off.

Self-relieving: The process by which excessive internal body cavity pressure is automatically relieved either into the
upstream or downstream line - generally found in ball valves.

Shrinkage: Internal defect in castings that are internal voids, irregular in shape, caused by volume contraction during
solidification. Can be caused by not maintaining a fluid channel to the riser during solidification.

Socket weld end (SWE): The end connection of a valve suitably prepared for socket welding to a connecting pipe.

Sour gas: Natural gas containing significant amounts of hydrogen sulfide (H2S). Requires special material treatments to
avoid failures from sulfide corrosion cracking.

Specification: A document that defines the requirements that a finished product must conform to - may include chemical
and mechanical properties, tolerances, marking, shipping, etc.

Spur gear: The simplest of gears - in a gear set, the pinion and ring gear are aligned on parallel shafts. Can be added to
another gear operator to further increase the mechanical advantage afforded by the gear.

Square operating nut:
A nut, usually 2" x 2", which is attached to a valve stem or the pinion shaft of a gear operator
allowing use of wrenches to quickly operate the valve.

Stainless steel (SS)
: Any of a number of types of iron alloy with chrome, nickel, or other elements that does not oxidize in
free air.

Stem: The rod or shaft transmitting motion from an operator (handwheel or gear operator) to the closure element of the
valve.

Stem nut (yoke nut): The threaded nut that surrounds a reciprocating valve stem and causes the stem to move when the
nut is rotated.

Stud: A bolt, threaded on both ends, often used in bolting together bodies and bonnets or bodies and closures.

Swing check valve: A check valve in which the closure element is a hinged clapper which swings or rotates about a
supporting shaft.

Tensile strength
: The highest tensile stress that a material can withstand before failure or rupture occurs - the force
being applied in a direction tending to elongate the material.

Tensile test: A destructive test performed on a specially machined specimen taken from material in its delivered condition
to determine mechanical properties, such as tensile strength, yield strength, and percent elongation.

Throttling: The intentional restriction of flow by partially closing or opening a valve.

Thrust: The net force applied to a part in a particular direction - e.g., on the end of a valve stem.

Torque: The rotational force imposed on or through a shaft, usually expressed in foot-pounds.

Trim: Commonly refers to the valve’s working parts and to their materials. Usually includes seat ring sealing surfaces,
closure element sealing surfaces, stems, and back seats. Trim numbers which specify the materials are defined in API 600
and API 602.

Trunnion: The part of a ball valve which holds the ball on a fixed vertical axis and about which the ball turns.  

Turns to operate: The number of complete revolutions of a handwheel or the pinion shaft of a gear operator required to
stroke a valve from fully open to fully closed or vice versa.

Ultrasonic inspection: An inspection procedure using high frequency sound waves to detect wall thickness or flaws
throughout the thickness of metal parts. Abbreviated as UT.

Union bonnet: A type of valve construction in which the bonnet is held on by a union nut with threads on the body.

Valve: A device used to control the flow of fluid contained in a pipe line.

WOG: Water-oil-gas - a rating designation generally used for small valves chiefly in low ratings. Indicates maximum working
pressure at ambient + 32° F to +100º F. Also called Nonshock Rating.

Working pressure (WP):
The pressure (pounds per square inch) at which a valve is designed to operate.

Wall thickness: The thickness of the wall of the pressure vessel or valve. For steel valves, minimum thickness
requirements are defined in ASME B16.34, API 600, and API 602.

Worm gears: A gear set in which the input shaft is offset from and perpendicular to the output shaft, and driving gear is
very small and perpendicular to the driven gear. Worm gear operators are used on ball valves.

Yield strength: The limiting stress beyond which a material will sustain permanent deformation.

Yoke: The part of gate or globe valve which acts as a bracket to support the top or outer end of the stem and stem
bearing.